smtplaza is majoy in supplying Juki smt feeder, Juki Stick Feeder, juki emboss feeder,juki 2070 feeder, juki VIBRATION STICK FEEDER,juki smt tape feeder.With prompt, professional, friendly service at competitive prices, and wonderful warranty service. We will find virtually any part you are looking for, regardless of original manufacturer or vintage, delivered anywhere in the world . Juki Smt Feeder Calibration Instrument,Juki Smt Feeders,JUKI Used Machine Feeder,Juki Stick Feeder,Juki Feeder Calibrator,Juki Electronic Feeder SMTPLAZA CO., LIMITED , https://www.smtpartsupply.com
Wall-hung boiler thermostat installation location The thermostat installation location should be far away from the radiator, away from the doors and windows, otherwise the heat is just hot, the boiler will stop, and the door and window will start when the boiler is opened. The thermostat installation height is about 1.4 meters (at the same level as the light switch) and the distance between the doors and windows is more than 0.8 meters. Pre-embedded rectangular box in the selected location, ordinary 86-type switch box can be, and from here to the boiler direction leads to the line tube.
1, easy to operate place;
2, where the average temperature can be covered;
3, where people have more activities (such as living room, bedroom, etc., according to family members' living habits);
4, can avoid the cold source, heat source, wind road;
Simple wall-hung boiler thermostat retention method
1, in the installation of temperature controller position down a small slot (to embed the depth of the line can be) to the ground, the line along the wall with placed, along the wall until the bottom of the boiler;
2. Open a small slot under the wall of boiler wall to the position where you want to exit the line, and bury the line;
3. The line in the wall of the wall should be fastened with a small line card;
4, the slot can be flattened;
5, wire diameter 2 × 1.0 is appropriate, as long as it can continue to use.
The simple method does not affect the laying of the floor. Be careful not to let the decorator cut the line. Different types of units, in the decoration can be their own hands-on wiring.
Wall-hung boiler thermostat wiring position
1, in the bottom side of the boiler, arbitrarily selected wiring;
2, pre-embedded rectangular box, and with a box lid with a hole in the middle;
3, threading with 2 × 0.75 and above the diameter of the multi-strand twisted-pair cord (phone line, lamp line can be, but to two), threading room reserved 0.5 meters, wall-hung boiler reserved 1 meter.
4. Put the reserve line in a box and put it in the box. Then use the same size hard foam to seal the box (so that someone can pull it).
Wall-hung boiler thermostats indicate that any manufacturer's thermostat can be used, only paying attention to the voltage below 6V. The benefits of installing and wiring the temperature controller of the boiler manufacturer are beneficial to the warranty. Otherwise, the thermostat will cause the boiler malfunction. If the two companies do not repair, you will find it difficult to do so. There is no compatibility problem with the thermostat, and there is no manual voltage. The programmed installation of two AA batteries is available for two years with a voltage of 3V.
Wall-hung boiler thermostat installation is very necessary. When Sunwell installs wall-hung boiler heating for users, it will propose to install wall-hung boiler thermostat, because the installation of wall-hung boiler thermostat directly affects the heating effect and energy-saving, and the user controls. It is very convenient, especially suitable for heating large-scale family use, small-sized home heating taking into account the installation cost, can be installed selectively.
Wall-hung boiler thermostat installation tutorial
Wall-hung boiler thermostat is an indoor temperature control system, which can accurately control the indoor temperature, to achieve the purpose of energy saving and comfort. Wall-hung boiler thermostat is a more important and practical element in the boiler element, but many installation companies in order to save the installation The cost is often not for users to install the boiler thermostat, but the use of water separators for temperature control, but the use of boiler thermostats will be more obvious.