Water-based car must know common sense

The people who choose to buy a residential car are basically planning to use it as their second home. Therefore, when using a residential car, everyone should pay attention to some related issues. After gradually getting familiar with the car, you will feel that most of the things in the car are still similar to some of the equipment in the home. The water supply system above the vehicle is equivalent to speaking. If there is no water supply system, the RV cannot be called a RV. Although both the wastewater system and the water supply system exist at the same time, they can actually be considered as one. The water in the water tank of a general passenger car is a 12V automatic pressurized water supply pump. After the switch of the water supply pump is turned on, it can pressurize the water supply pipe in the car to twenty to forty PSI. The clean water tank device built into the car has a lockable fresh water inlet that can use the water pipe outside the car to directly fill the water tank. Another way of water supply is to use an external water pipe. The water pipe in the car is directly connected to the faucet in the campsite. This way, the pressure pump is not used. If the tail water outside the car cannot be used, the car's pressure pump will automatically provide water.

旅居车用水必知常识.jpg

If water is used inside the RV, it must be remembered to turn off the water supply pump, because if there is no water supply in the clean water tank, the water supply pump will still continue to operate and it will be easier to do so. Damaged water pump. If an external water pipe is to be used, the water in the water supply system must be reduced by filling the water pipe with water before receiving the water from the campsite. Excluding the air in the water pipe is actually very simple. Fill the clean water tank in the car with water in advance, and then turn on the water supply pump. Then turn on all the water taps in the car until you see it in the water tap. When the water came out, it proved that the air had been eliminated.

The amount of water in the clean water tank and waste water tank in the car must be checked in a timely manner, and it must be dumped in time before being filled. There is a special RV sewage treatment pool in foreign countries. After the conduits and drainage joints are connected, the wastewater is discharged into the sewage treatment pool in the campsite. However, at present, there are no such facilities in the country. Therefore, we can only use the drain pipe to connect the drain valve of the waste water tank and then discharge the waste water into the ditch. However, the water in the black water tank can only be taken to the public toilet for dumping if it does not support the discharge of sewage.


   Round Downpipe Roll Forming Machine is used for building, it can as rain gutter uses. 

   This machine includes one set decoiler, guiding equipment, main roll forming machine, PLC control system, hydraulic cutting and receving table. 

    It has two cutting modes: flying saw cutting and mould cutting. 


Specifications:

Raw material PPGI or GI
Material thickness range 0.2-0.8mm
Rollers 18 rows
Material of forming rollers 45# steel with chromed
Shaft diameter and mateiral 76mm, material is 40Cr
Material of cutting blade Cr12 mould steel with quenched treatment
Forming speed 12-15m/min(excluding cutting stoping time)
Main motor power 4 KW
Hydraulic station power 3KW
Mode of cutting Hydraulic cutting or flying saw cutting or mould cutting
Control system PLC Frequency Control System with touch screen


Working process:

Working process

Decoiler - Feeding guide - Main roll forming machine - PLC control system - Hydraulic cutting - Receiving table


Pictures of machine:

Round gutter

Round Downpipe Roll Forming Machine


Round Downpipe Roll Forming Machine

Round Downpipe Roll Forming Machine



Training and Installation :
1. We offer installation service local in paid, reasonable charge. 
2. QT test is welcome and professional.
3. manual and using guide is optional if no visiting and no installation. 

Certification and after service:

1. Match the technology standard, ISO producing certification 
2. CE certification 
3. 12 months warranty since the delivery. Board. 

Our advantage:

1. Short delivery period. 
2. Effective communication 
3. Interface customized. 

Round Downpipe Roll Forming Machine

Round Downpipe Roll Forming Machine,Gi Round Downpipe Roll Forming Machine,Gl Round Downpipe Roll Forming Machine,Round Downpipe Roll Cold Forming Machine

YingYee Machinery and Technology Service Co.,Ltd , https://www.yingyee.cn