Guidance: When drilling with a magnetic drill, ensure that there are no iron or other debris under the magnetic seat of the drill, the adsorption surface remains flat, and the machine can not shake or fail to fully absorb. Because if the machine does not suck well on the steel plate during drilling, the machine shakes and the drill bit is damaged. If there is a relatively thin steel plate, add some metal plates to the bottom to increase the suction of the rig and plate. Many steel friends use magnetic hollow drill bits to drill holes. But there will be different results for different workers using the same drill bit. Some masters can use the same drilling rig to drill holes with the same number of bits. Some have little punch. This situation does not eliminate the quality of the drill itself. But the big reason is that the method and experience of the drilling of the workers' masters are determined. Here are some simple things to note.
HEPA filters
Describe:
High-efficiency Air Filters are mainly used to trap dust and suspended matter below 0.5um. The air purifier mainly consists of two parts: the filter core and the shell .
The basic requirements are high filtration efficiency, low flow resistance, and can be used continuously for a long time to reduce the cost of later consumables.
The filter element is the Air Filter , and the high-Efficiency Air Filter plays an important role in the air purification industry.
Characteristics:
Using ultrafine fiberglass paper as Filter Material, offset paper, aluminum film and other materials as partition board, glued with wood frame aluminum alloy, using special silicone rubber, no smell, no surface hardening, no crack for a long time, stable chemical properties, Corrosion resistant, can absorb the stress produced by thermal expansion and cold shrinkage without cracking, soft and hard, elastic recovery.
Each set is tested by sodium flame method. It has the characteristics of high filtration efficiency, low resistance and large dust capacity.
Applications:
High efficiency air filters can be widely used in optoelectronics, LCD liquid crystal manufacturing, biomedicine, precision instruments, beverage and food, PCB printing and other industries dust-free purification workshop air conditioning terminal. High efficiency and super high efficiency filters are used at the end of clean room. According to their structure, they can be divided into three types: high efficiency with partition board, high efficiency with no partition board, high efficiency with large air volume, super high efficiency filter and so on.
Hepa Air Filters,Hepa Filter,Intermediate Air Filters,Medium Effect Air Filters Henan Sinofiltec Technology Co.,Ltd , https://www.airfilters.pl
The first thing is definitely whether the check is correct or not. Whether the screw is tightened. The drill is installed.
1: When using hollow drill bit, coolant must be used for drilling work.
2:Different specifications of drills drill different material metal plate drilling speed also has certain requirements. The larger the drill bit, the lower the drilling speed. A simple drill speed table
3: Before starting the drilling, make sure that the tool has been fully installed and there is no loose or clamped phenomenon. In particular, if the taper shank magnetic drill or rocker drill is to be used with a conversion sleeve, it should be checked whether the installation of the conversion adapter is in place or not. An additional component in the shank drill rig with the drill bit has a hidden danger.
4: When drilling with a magnetic drill, ensure that there are no iron or other debris under the magnetic seat of the drill, the adsorption surface remains flat, and the machine can not shake or fail to fully absorb. Because if the machine does not suck well on the steel plate during drilling, the machine shakes and the drill bit is damaged. If there is a relatively thin steel plate, add some metal plates to the bottom to increase the suction of the rig and plate.
5: The hollow drill bit infeed must be performed slowly. Cut into steel plate about 1mm and then force it evenly. If there is a stuck condition, you should cut off the power first, then manually turn the tool slightly in the opposite direction and then put forward the drill to check the situation. Can't drill down hard. The feed speed and the speed of the knife need to be slow, and when the middle is progressed, the feed speed should be uniform. As for the speed control, it depends on the experience of the various workers' masters.
6: If you need to play a thick steel plate you can not drill holes once. You can drill first and then exit to remove the lower scraps and continue drilling. Drilling was done multiple times. Sometimes too much swarf affects the drilling operation.
7: If there is severe vibration when cutting in, check whether the rotating speed is too high. Also check if the clearance of the machine guide is too large.
8: The drill usually maintains and stores as far as possible to avoid touching the blade edge, so as not to damage the drill bit
9: Try to avoid overlapping drilling of steel plates. If it is necessary to overlap the drill hole, drill the second block after removing the core after drilling the first block.
