Recently, Karyou “Lai Yuquan†shared some experiences on pre-judgment driving in the forum post “Truck Predictive Driving—Safetyâ€. Trucks are bulky, heavy-duty, have relatively poor braking performance, and have many blind spots. The direct linking of interests and other specialties has created a difference between the high accident rate of trucks and the level of operating efficiency. How to reduce and avoid safety accidents in daily driving is especially important for predictive driving. â— Before the car lights to slow down to leave a safe distance for turning When your own vehicle sees the turning lights in front of the car or the brake lights are on during normal driving, you should first judge whether or not you will make a turn. The correct approach at this time should be to loosen the throttle, open the exhaust brake, and prepare the brakes on the right foot, while observing whether there is enough space to overtake or avoid the opposite lane. When making a right turn in front of the car, it should be decelerated to allow the front car to make a turn first. At the same time, if there are other vehicles in front, it is possible to speed up the passage if safety is confirmed. Make sure to leave a safe distance in the driving process, especially behind the car, to prevent brake problems or drivers react slowly and cause safety accidents. â— There are pedestrians on the road to reduce people's speed On the roadside, if someone is watching right and left and is trying to cross the road, the right way for the driver to do so is to lose the throttle, open the exhaust brake, and prepare to brake on the right foot. Observe the pedestrian's actions closely. If you confirm that the passerby is really crossing the road, you should guess the brakes and leave a safe distance for pedestrians. If the pedestrian does not cross the street or let the vehicle go first, the driver cannot blindly accelerate the passage. The correct approach should be to start accelerating after the car passes pedestrians, so as to ensure that no safety accidents will occur. Do not avoid seeing time when passers-by cross the road and passers-by to grab time, so often will get more than gains, security incidents. â— It is important not to grasp the time before the traffic lights Because of the continuous occurrence of security incidents involving grabbing traffic lights, their willingness is often due to grab time. When the vehicle reaches the traffic light, it should slow down and observe it. For example, when the green light is only a few seconds away, it should be throttled and slowed down. Do not grab a few seconds. When the green light remains for a few seconds, you must not follow the front car's red light. Under such circumstances, you can't judge whether the front car will be braked in front of the green light. It is often thought that following the front car, it will cause an accident. The rear-end chase is full responsibility. Really lost his wife and folded soldiers. In the case of a red light in front of the car or a red light in front of the car, it should be decelerated in advance, lose the throttle, and let the vehicle slide slowly. This will save fuel and save brake pads. â— Children on the roadside should pay attention to observe slowdown and prevent accidents It is the most “headache†to have children play while driving. The child’s safety awareness is poor. When encountering this kind of situation, it should be decelerated in time and the brakes should be prepared. Always pay attention to the children's movements and prevent children from suddenly running into the road and causing safety accidents. When you pass through a child, you should keep the speed low, observe the distance between the vehicle and the child at any time, and at the same time, leave sufficient safety distance on both sides. In some streets or places where pedestrians are densely covered, vehicles should be allowed to slow as much as possible to prevent pedestrians and vehicles from colliding with each other under the wheels. â— Postscript Actually, as a driver, when driving any vehicle, he intentionally or unconsciously uses the “predictive driving†method to take measures in advance in various road conditions and various emergencies. But do pay attention! This kind of prejudgment is definitely not taken for granted. "I think the other person..." This "thought" is a misjudgment, which is the nature of guessing and even gambling. Because we are all ordinary people, there is no "reading mind" and you will never know what other people think. Zinc Alloy Die Casting of Sanitary Ware have a good surface roughness, strength and elongation, Which are widely used in a variety of ornaments, such as furniture, accessories, door handle ,architectural decoration, bathroom accessories, lighting parts, toys, tie clips, belt buckles, various metal buckle and so on,they are required a good surface treatment performance. Zinc Alloy Die Casting of Sanitary Ware Zinc Die Casting Sanitary Part, Zinc Sanitary Part Ningbo Zhenhai Xinxie Machinery Co.LTD , https://www.xinxie-diecasting.com
Zinc Alloy Die Casting of Sanitary Ware have their own purposes, need to meet the performance requirements.
(1) mechanical properties, tensile strength, when the material fracture resistance;Elongation, brittleness and plasticity of the measure;Hardness is the resistance of the material surface is pressed into a hard object or friction caused by plastic deformation.
(2) state of the working environment: temperature, humidity, media contact with the workpiece and air tightness requirements.
(3) precision: accuracy and dimensional stability can be achieved.